{{datatype|expand}} {{datatype|expand}} {{datatype|expand}} {{datatype|expand}} {{datatype|expand}} {{datatype|expand}} {{datatype|expand}} {{datatype|expand}} {{datatype|expand}} {{datatype|expand}} {{datatype|expand}} This parameter is DEPRECATED and is replaced by {{param|MaxFAPTxPowerExpandedConfig}} in order to define the expanded value range. This parameter replaces {{param|MaxFAPTxPowerConfig}} which is DEPRECATED in order to define the expanded value range. Indicates whether the FAP supports the self-configuration capability to determine the Maximum FAP Transmit Power. If {{true}} a range of values MAY be provided in {{param|.CellConfig.UMTS.RAN.FDDFAP.RF.MaxFAPTxPowerExpanded}} for the FAP to select from. If {{false}} only a single value SHOULD be provided in {{param|.CellConfig.UMTS.RAN.FDDFAP.RF.MaxFAPTxPowerExpanded}}. This parameter is DEPRECATED and is replaced by {{param|MaxFAPTxPowerExpandedSelfConfigEnable}} in order to define the expanded value range. This parameter replaces {{param|MaxFAPTxPowerSelfConfigEnable}} which is DEPRECATED in order to define the expanded value range. Indicates whether the self-configuration capability in the FAP is used or not to determine the value of {{param|.CellConfig.UMTS.RAN.FDDFAP.RF.MaxFAPTxPowerExpanded}}. If {{true}} The FAP self-configures the value. If {{false}} The ACS MUST provide the specific value to be used. Indicates whether the self-configuration capability in the FAP is used or not to determine the values of {{param|.CellConfig.UMTS.CN.LACRAC}} and {{param|.CellConfig.UMTS.RAN.URAList}}. If {{true}} The FAP self-configures the value. If {{false}} The ACS MUST provide the specific value to be used. Port number of FAP-GW used for initial Iuh SCTP contact. This value is specified as 29169 according to IANA definition per {{bibref|IANA-portnumbers}}, registered on 2009-09-08. Use of IANA-defined value is recommended. This object contains parameters relating to Access Management (ACL, CSG, LIPA). Closed Subscriber Group (CSG) service behavior is specified in {{bibref|3GPP-TS.22.011}}. Note: Cell barring and 3GPP access class parameters are contained in {{object|.CellConfig.UMTS.RAN.FDDFAP.CellRestriction.}} (UMTS FAP). Indicates the type of access mode the FAP operates in. {{enum}} When the value is not {{enum|Open Access}} non-CSG-capable UE are handled according to {{param|NonCSGUEAccessDecision}}. Note: This parameter controls the setting of the CSGindicator bit, specified in MIB in {{bibref|3GPP-TS.25.331}} (for UMTS FAP). Maximum number of concurrent UEs allowed at a cell. Valid for any {{param|AccessMode}}. A value of -1 allows an unlimited number of concurrent UEs up to the limit of FAP capacity. The setting does not affect emergency calls. This parameter is DEPRECATED and is being replaced by {{param|HNBName}}. This parameter is DEPRECATED and is being replaced by {{param|HNBName}}. This parameter replaces {{param|HNBIdentifier}} and {{param|HomeZoneName}} which are DEPRECATED. Home NodeB name. An operator-defined string that is broadcast by a CSG cell or a hybrid cell and displayed on the UE for the purpose of manual cell selection or indication that the UE is camped on the cell as specified in {{bibref|3GPP-TS.22.220|Section 5.4.2}}. Corresponds to parameter 'hnb-Name' specified in SIB20 in {{bibref|3GPP-TS.25.331|Section 10.2.48.8.23}} for an UMTS FAP. This parameter is DEPRECATED and being replaced with {{param|MaxCSGMembers}}. Maximum number of concurrent CSG member UEs allowed at a hybrid or closed cell. A value of -1 allows an unlimited number of CSG members up to the limit of FAP capacity. The setting cannot be larger than the value of {{param|MaxUEsServed}}. The setting does not affect emergency calls. {{bibref|3GPP-TS.22.011}}, {{bibref|3GPP-TS.22.220}}. Maximum number of concurerent non-CSG member UEs allowed at a hybrid cell. Valid only if {{param|AccessMode}} is {{enum|Hybrid Access|AccessMode}}. The setting cannot be larger than the value of {{param|MaxUEsServed}}. The setting does not affect emergency calls. Maximum percentage of physical resource that can be assigned to non-CSG members aggregately at one time. In an UMTS FAP, this applies to RB resource. Defines the Closed Subscriber Group of the Access Control List. An UMTS FAP broadcasts this CSG ID in SIB3 depending on the AccessMode. The "realm" portion of the HNB-ID where HNB-ID is defined in {{bibref|3GPP-TS.25.469}} v8.2.0 and is shown as follows: 0<IMSI>@<realm> Or 1<OUI>-<SerialNumber>@<realm> The other identifiers before "@" are device dependent values. Both <OUI> and <SerialNumber> are defined in {{bibref|TR-069a2|Table 36}}. <IMSI> is obtained from the USIM if it is equipped in the FAP. This parameter is DEPRECATED and replaced by {{param|PowerRampStepUp}} in order to correct and align the parameter name to the intended purpose. This parameter replaces {{param|PowerRampSetup}} which is DEPRECATED in order to correct and align the parameter name to the intended purpose. Used for the Uplink Common Channel. Defines the Power ramp setup, specified in {{units}}, on PRACH preamble when no acquisition indicator (AI) is detected by the UE. Parameter in SIB5. {{bibref|3GPP-TS.25.331|Section 10.3.6.54}} This parameter is DEPRECATED and is replaced by {{param|MaxFAPTxPowerExpanded}} in order to expand the value range. This parameter replaces {{param|MaxFAPTxPower}} which is DEPRECATED in order to expand the value range. Defines the maximum transmission power allowed on the FAP, maximum value for the linear sum of the power of all downlink physical channels, that is allowed to be used in a cell. {{param}} is expressed as a range of allowed maximum power levels with ".." (two periods) between the upper and lower values, i.e. "<Pmax_low>..<Pmax_high>". {{param}} identifies the limits between which the FAP can self-configure its maximum transmit power. Self-configuration for maximum transmission power is controlled by {{param|.Capabilities.UMTS.SelfConfig.MaxFAPTxPowerExpandedConfig}} from an availability perspective and {{param|.FAPControl.UMTS.SelfConfig.MaxFAPTxPowerExpandedSelfConfigEnable}} from an enabled perspective. <Pmax_low> and <Pmax_high> are measured in dBm and have a range of -30.0 to 20.0 incremented by 0.1 dB. {{bibref|3GPP-TS.32.642|Section 6.3.9}} {{bibref|3GPP-TS.25.104|Section 6.2.1}} This parameter is DEPRECATED and is replaced by {{param|MaxFAPTxPowerInUseExpanded}} in order to expand the value range. This parameter replaces {{param|MaxFAPTxPowerInUse}} which is DEPRECATED in order to expand the value range. The maximum transmission power measured in {{units}} currently used by the FAP. Actual values of the maximum transmission power are -30.0 {{units}} to 20.0 {{units}} in steps of 0.1 dB. The value of {{param}} divided by 10 yields the actual value of the maximum transmission power. Self-configuration for maximum transmission power is controlled by {{param|.Capabilities.UMTS.SelfConfig.MaxFAPTxPowerExpandedConfig}} from an availability perspective and {{param|.FAPControl.UMTS.SelfConfig.MaxFAPTxPowerExpandedSelfConfigEnable}} from an enabled perspective. If the self-configuration capability is available and enabled, this parameter indicates the value selected by the FAP among the range provided in {{param|MaxFAPTxPower}}. If the self-configuration capability is not available or not enabled, then this parameter contains a value selected by the ACS. If the SecGW parameters are configured then this parameter determines whether the CWMP traffic will be sent across the IPsec tunnel or outside of the IPsec tunnel. If {{false}} then the CWMP traffic will be sent outside of the IPsec tunnel. If {{true}} then the CWMP traffic will be sent across the IPsec tunnel. Virtual Interfaces used for associating the tunnel (ephemeral) childSA pairs with the QueueManagement framework defined in the used root data model: * For the Device:2 root model specified in {{bibref|TR-181i2}} the Device.QoS.Classification.{i}. and Device.QoS.Queue.{i}. objects can be associated with these interfaces. * For InternetGatewayDevice root model specified in {{bibref|TR-098}} the InternetGatewayDevice.QueueManagement.Classification.{i}. and InternetGatewayDevice.QueueManagement.Queue.{i}. objects can be associated with these interfaces.